California Coverage · Tulare County
Tulare County base maps & site data for designers
The existing-conditions base map and pre-design site analysis that normally takes a half-day across county GIS portals and hand-tracing into CAD — for any Tulare address, from Visalia to the Sierra foothills, in about a minute.
What Lekua resolves in Tulare County
Every layer below is pulled live from Tulare’s own GIS and authoritative state sources the moment you enter an address — no manual tracing, no generic insets, every source cited.
County assessor parcel boundary with APN, address, and lot area, with the statewide CA parcel layer as fallback.
Fine 1–2 ft contours generated on-demand from the 1-meter USGS 3DEP elevation model — far finer than the 10-ft national data most tools show.
County-hosted building footprints, gap-filled with FEMA national structures for anything the county layer misses.
CAL FIRE FHSZ severity checked for the parcel, with defensible-space perimeters drawn where the parcel sits in a designated zone.
USDA SSURGO soil profile, historical rainfall, and modeled seasonal sun-hour heat maps for the parcel.
California natives matched to the site’s soil and microclimate, plus lawn-replacement rebate estimates from the serving provider — City of Tulare (Water Department) and local programs.
Fire risk, checked rather than assumed
Most Tulare parcels sit outside mapped fire-hazard severity zones — but the foothill and Sierra edge east of Porterville carries designated zones. Lekua checks the parcel against the current CAL FIRE 2024–25 maps rather than assuming either way, and draws defensible-space perimeters only where they apply.
- Parcel-level FHSZ check against the current CAL FIRE 2024–25 maps.
- Zone 0 / 1 / 2 perimeters drawn only where the parcel is in a designated zone.
- Every recommended plant still carries its flammability data.
Zoning setbacks, by jurisdiction
Setbacks in Tulareare set per town, not countywide. Lekua resolves the parcel’s jurisdiction and zone code and encodes each jurisdiction’s adopted setback table, citation and all. Setback rings are drawn only after a table passes independent panel review — until then the export carries the code-cited values with an explicit “unverified” advisory instead of lines we can’t stand behind.
A native palette, enriched beyond the plant list
Start from the Calscape native plant database — then get the research-backed traits Calscape alone doesn’t put at your fingertips, matched to the parcel’s exact soil, sun, rainfall, and microclimate. Hand a client a list that’s code-compliant, climate-appropriate, and built to perform.
Flammability and defensible-space zone suitability from Las Pilitas burn-time research and UCANR / CAL FIRE-aligned fire-safe lists — not just a name on a list.
Slow / moderate / fast growth plus mature height and spread, so spacing and time-to-fill are realistic from day one.
Calscape cultivation and longevity guidance, so the palette reads for how it performs over 10–20 years, not just at install.
WUCOLS-aligned water-use ratings (for the MWELO budget) and pollinator / bird support scores on every species.
Plant data: Calscape / CNPS, enriched with Las Pilitas burn-time research, UCANR & CAL FIRE-aligned fire-safe lists, and WUCOLS water-use ratings.
Water districts & rebates
Lawn-replacement rebate estimates are matched to the serving district: City of Tulare (Water Department) · California Water Service — Visalia District.
Tulare County base map FAQ
Can I get a CAD base map for a Tulare County parcel?
Yes. Enter any Tulare address and export a layered DXF (AutoCAD-compatible) with parcel lines, building footprints, on-demand 1–2 ft contours, and spot elevations — plus a designed PDF site report for the client.
What contour interval is available in Tulare County?
Lekua generates fine 1–2 ft contours on-demand from the 1-meter USGS 3DEP elevation model — far finer than the 10-ft national fallback most tools show, which matters wherever grading and drainage drive the design.
Does it include zoning setbacks for Tulare County?
Not yet — setback tables for Visalia, Porterville, and the county are not yet encoded, and the export never guesses: where a setback isn’t verified it says so plainly instead of drawing lines. Encoded tables follow the same review-gated process as other counties.
How does it handle defensible space and fire-safe planting?
Lekua checks the parcel against current CAL FIRE FHSZ maps, draws Zone 0 / 1 / 2 defensible-space perimeters around the structures where designated, and tags every recommended native with the zones it’s suited to.
Is the data current and reliable enough for submittals?
Layers are pulled live from county GIS, USGS, and CAL FIRE at export time, and any encoded setback table cites its source with a date. Everything is labeled “for planning reference — not for construction.” Verify against the current code and a stamped survey before submittal.
Start with a Tulare address
Free to search. Sign in to export the CAD base map and PDF site report.