California Coverage · Fresno County
Fresno County base maps & site data for designers
The existing-conditions base map and pre-design site analysis that normally takes a half-day across county GIS portals and hand-tracing into CAD — for any Fresno address, from Fresno to Shaver Lake, in about a minute.
What Lekua resolves in Fresno County
Every layer below is pulled at export time from county, state and national GIS sources the moment you enter an address — no manual tracing, no generic insets, and the sheet cites which source drew each layer.
County assessor parcel boundary with APN, address, and lot area, with the statewide CA parcel layer as fallback.
Fine 1–2 ft contours generated on-demand from the 1-meter USGS 3DEP elevation model — far finer than the 10-ft national data most tools show.
National building outlines (Overture Maps’ mixed mapped and machine-learned outlines where a county cut is imported, otherwise FEMA USA Structures with Microsoft machine-learned outlines where FEMA has none), drawn dashed and tagged as remote-sensed. The county publishes no footprint layer of its own, and the export says exactly which source drew.
USGS 3DEP’s 2019 FEMA Region 9 Fresno lidar point clouds: each structure’s roof is read from the lidar points inside its footprint and its base from bare earth around it; where the flights hold no points the sheet says which source answered instead. Where a record carries no height, the structure is labeled as having none rather than drawn at a confident wrong number.
CAL FIRE FHSZ severity (2024–25 remap) with Zone 0 / 1 / 2 defensible-space perimeters drawn around structures — pointed where it counts: the Sierra foothills and Creek Fire country above the valley floor.
USDA SSURGO soil profile, historical rainfall, and modeled seasonal sun-hour heat maps for the parcel.
California natives matched to the site’s soil and microclimate, plus the serving water supplier’s lawn-replacement rebate, shown only while it was verified on the supplier’s own page within 60 days.
Tuned for Fresno’s fire interface
The Sierra foothills and Creek Fire country above the valley floor sits in mapped fire-hazard severity zones, and defensible-space planting rules now shape those projects. Lekua draws the CAL FIRE Zone 0 / 1 / 2 perimeters on the plan and filters the plant palette to what each zone allows — fire-wise from the first pass.
- Zone 0 (0–5 ft ember-resistant), Zone 1 (5–30 ft), and Zone 2 (30–100 ft) perimeters drawn around the structures.
- Every recommended plant carries a defensible-space zone rating, so you place the right species in the right zone.
- Flammability ratings draw on Las Pilitas burn-time research and UCANR / CAL FIRE-aligned fire-safe lists.
A native palette, enriched beyond the plant list
Start from the Calscape native plant database — then get the research-backed traits Calscape alone doesn’t put at your fingertips, matched to the parcel’s mapped soil, sun, rainfall, and microclimate. Hand a client a list checked against the code, climate-appropriate, and built to perform.
Flammability and defensible-space zone suitability from Las Pilitas burn-time research and UCANR / CAL FIRE-aligned fire-safe lists — not just a name on a list.
Slow / moderate / fast growth plus mature height and spread, so spacing and time-to-fill are realistic from day one.
Calscape cultivation and longevity guidance, so the palette reads for how it performs over 10–20 years, not just at install.
WUCOLS-aligned water-use ratings (for the MWELO budget) and pollinator / bird support scores on every species.
Plant data: Calscape / CNPS, enriched with Las Pilitas burn-time research, UCANR & CAL FIRE-aligned fire-safe lists, and WUCOLS water-use ratings.
Water suppliers
Main water suppliers in Fresno County: City of Fresno Public Utilities · City of Clovis Public Utilities.
Fresno County base map FAQ
Can I get a CAD base map for a Fresno County parcel?
Yes. Enter any Fresno address and export a layered DXF (AutoCAD-compatible) with parcel lines, building footprints, on-demand 1–2 ft contours, and spot elevations — plus a designed PDF site report for the client.
What contour interval is available in Fresno County?
Lekua generates fine 1–2 ft contours on-demand from the 1-meter USGS 3DEP elevation model — far finer than the 10-ft national fallback most tools show, which matters wherever grading and drainage drive the design.
Are the building heights on a Fresno County base map measured or assumed?
Measured, wherever the county record carries one. USGS 3DEP’s 2019 FEMA Region 9 Fresno lidar point clouds: each structure’s roof is read from the lidar points inside its footprint and its base from bare earth around it; where the flights hold no points the sheet says which source answered instead. A structure whose record has no height is labeled as having none — the sheet prints an explicit no-data note instead of a plausible number, because a wrong ridge height is worse on a shade study than an admitted gap.
Does it include zoning setbacks for Fresno County?
Only where a table has been encoded and reviewed — the cards above list each one and say whether its envelope is drawn or only cited. Tables for Fresno, Clovis and most of the county’s cities are not yet encoded, and the export never guesses: where a setback isn’t verified it says so plainly instead of drawing lines.
How does it handle defensible space and fire-safe planting?
Lekua checks the parcel against current CAL FIRE FHSZ maps, draws Zone 0 / 1 / 2 defensible-space perimeters around the structures where designated, and tags every recommended native with the zones it’s suited to.
Is the data current and reliable enough for submittals?
Layers are pulled live from county GIS, USGS, and CAL FIRE at export time, and any encoded setback table cites its source with a date. Everything is labeled “for planning reference — not for construction.” Verify against the current code and a stamped survey before submittal.
Start with a Fresno address
Free to search. Sign in to export the CAD base map and PDF site report.